Furnace Repair in Portland, OR
Portland’s long, mild season wears heating systems differently than a hard winter. Many furnaces fail at the igniter, not the burner. We find the actual fault, quote it before we start, and restore heat. Same-day appointments are usually available, and we answer no-heat calls 24/7. We repair every major furnace brand, including equipment we did not install.
Customers rate us a 4.9 out of 5 
on Google.
Furnace and Heater Repair Portland Homes Actually Need
Gas Furnace Repair
Igniters, flame sensors, gas valves, pressure switches, inducer motors, and control boards. We diagnose with instruments instead of swapping parts until the heat returns. We check combustion and venting on every gas furnace call because it is a safety item, not optional.
24/7 Emergency Furnace Repair
No heat in a Portland January is not a next-week problem. We answer emergency calls any hour, every day of the year, with common failure parts already on the truck.
Heat Pump Heating Repair
Heat pumps are common in Portland because the climate suits them. We diagnose and repair reversing valves, defrost boards, and auxiliary heat controls, which are the usual suspects when a heat pump blows cool air in winter.
Portland’s Long Mild Winter Is What Wears a Furnace Out
Run hours, not freezing temperatures, are what age a Portland furnace. This city is gentle on heating equipment in one way and brutal in another.
ENERGY STAR certified furnace program labels equipment separately for the northern and southern halves of the United States. It rates efficiency through Annual Fuel Utilization Efficiency, or AFUE, plus blower motor efficiency. Oregon sits in the northern group, where homes demand more heat across a longer season.
A Portland winter day is rarely cold enough to keep a furnace running in a long steady burn. Instead, the system lights, satisfies the thermostat quickly, shuts down, then lights again shortly after. This cycle repeats thousands of times between October and April. Ignition is the hardest moment in a furnace’s life. Igniters, flame sensors, pressure switches, and inducer motors wear out by cycle count, not cold.
We diagnose with that pattern in mind. A Portland furnace that will not light usually signals accumulated cycles, not one bad night. We check ignition parts, the flame signal in microamps, and the static pressure the blower faces. An oversized furnace in a mild climate short-cycles more and fails sooner.
What Our Customers Say
Dmitry did an excellent job of figuring out what the cause was for our heat pump system not switching to gas heat when the temperature was below 35º which was a setting fix rather than a part replacement. After diagnosing the problem he did a nice system maintenance job including cleaning the heat pump compressor to like new condition. With other companies, they always suggested doing it myself.
Inspected and do any needed maintenance. The furnace had stopped working, although my son in-law was able to clean some corrosion and get it working again until the tech could make a visit (it was a low of 19 degrees that night). Anastasia was able to work us in a couple of days from our initial call instead of the 1-2 week lead time of other companies in the area. This was much appreciated as it was Christmas weekend and a big storm was blowing through Tigard. Alex showed up, did a thorough check-up, did some adjustments and declared the system good to go (just needed a new air filter). Thanks to the Conrad Crew for a great job!
Fantastic service. excellent in all aspects. I would recommend Conrad Heating for anything related to heating, cooling, air conditioning tuneup and duct cleaning
Signs Your Portland Heater Needs Repair Now
Heating systems rarely quit without warning. They degrade through autumn and fail on the first cold night. Act on these signals early.
- The furnace starts then quits within a minute. Short cycling points to a flame sensor, pressure switch, or oversized system.
- You hear repeated clicking with no ignition. The igniter or flame sensor is failing. This is the most common Portland furnace fault we see.
- Rooms at the end of the duct run stay cold. Airflow is restricted somewhere, often in crawlspace ducts that have separated or lost insulation.
- A burning smell that does not clear after the first hour. Dust burn-off at the start of the season is normal. A persistent smell is not.
- The blower runs constantly, but the air is cool. On a heat pump, this usually points to the reversing valve or the defrost board.
- Heating costs climbed with no change in habits. Lost efficiency usually means restricted airflow or a system past its service life.
- A carbon monoxide alarm has sounded, even once. Leave the building and call from outside. Don’t relight anything until the appliance has been inspected.
If two or more apply, book before the cold arrives, not during it. December slots are the hardest to get in this city.
Our Furnace Repair Process, Step by Step
The sequence stays the same on every heating call. This keeps the diagnosis clear when the house is cold, and everyone is rushing.
- Symptom interview. What the system did and when. The pattern narrows the cause before removing a panel.
- Combustion and venting safety check. On any gas appliance, this comes first. We check the heat exchanger, vent connection, and combustion air before relighting anything.
- Thorough diagnosis. We check flame signals in microamps, gas pressure, temperature rise, static pressure, and electrical values across the ignition circuit.
- Findings explained. We name the failed component, what caused it, and anything else close to failing.
- Written price approved first. You agree on the figure before work starts. If the repair is poor value for a system this age, we say so.
- Repair and verification. We complete the work, run a full heating cycle, and confirm the temperature rise stays within the manufacturer’s range.
We answer no-heat calls any hour, any day, holidays included. If a component must be ordered, we say so immediately and do what we can to keep the house habitable in the meantime.
(503) 785-9715
Why Portland Picks Conrad for Heating Repair
Licensed and Insured Team
Our Oregon CCB license, CCB #238277, reflects our commitment to professional, accountable furnace repair. We are also fully insured for added peace of mind.
Same-Day and Emergency Service
We can schedule most heating repair calls received before 5 PM for the same day across the Portland metro area. Our dispatch line is open 24/7. You will reach a real person, not voicemail or a callback queue, and a technician is usually on-site within two hours.
Upfront Written Pricing
You approve a fixed figure before work begins. If the fault is different, we requote before continuing. Nothing appears on the invoice without your agreement.
Every Major Brand Serviced
We are a certified RUUD dealer and a Bosch equipment dealer. Our technicians work on every other major furnace and heat pump brand. It does not matter who installed it.
Maintenance Agreements That Prevent The Call
Members get two visits a year and a 10% discount on repairs and installations. It includes priority scheduling and after-hours service at standard rates.
A Referral Program Instead Of Advertising
Our loyalty referral program rewards customers who send neighbors our way. Most of our growth comes from referrals, which only works when the repairs hold.
Book Furnace Repair Before the Next Cold Snap
We provide full-scale heating services in Portland and surrounding areas. One team also covers the rest of the heating system, including installation, replacement, and maintenance to prevent the next failure.
The cheapest heating repair is the one booked in October, not during the first freeze. Slots are easier to get, parts are easier to source, and you are not choosing under pressure.
Areas We Serve
From quick repairs to full installations and replacement services, we’re expertly trained to take on HVAC jobs of all sizes.
We focusing on serving:
